Table of contents
- What happens when a dealer returns one controller out of 200?
- How do you set up serial number tracking for electronics in Bimp?
- How does a claim analysis by serial number look?
- How much does a warranty repair cost, and why does it need its own cost?
- What should you prepare before launching serial tracking?
- What does this give the company?
- Scenario limits
- FAQ
- Serial number tracking for electronics ties a unit's serial number to the batch of components, the assembly date and the dealer. For the fictional controller this takes 15 minutes per claim instead of a working day.
- In strict mode Bimp does not let you sell a unit without choosing a specific series, so a number always shows who received it. A repair is processed as a separate production order with its own cost.
- A batch of 200 radio modules went like this: 140 sold to dealers and 60 in stock. The upper estimate for replacing modules in every sold unit is €1,540, so the decision rests on numbers.
The company is fictional. Every action in Bimp is a real product feature. The figures in the example are invented.
Serial number tracking for electronics answers three questions when a dealer returns one controller: when it was assembled, from which components, and to whom the other units of the same batch were sold. At Gravent Controls (a fictional company) such an answer used to take a working day. After setting up series in Bimp it takes 15 minutes.
The difference follows from simple arithmetic. Twelve claims a month at 8 hours each give 96 hours, and at a quarter of an hour that is 3 hours. The saving is 93 hours a month, and it is the time of the process engineer and the warehouse manager.
What happens when a dealer returns one controller out of 200?
Gravent Controls makes controllers for heating systems and greenhouses. The staff is 25 people, and assembly runs in batches of 200 units. Controllers are bought by dealers in several regions and a few direct customers, and the warranty lasts 24 months.
A dealer sends one unit with the complaint “loses connection”. Who assembled it, which modules sit inside and whether anything was replaced before are searched for in three tables: the warehouse sheet, the process engineer’s table and the service log. If the cause lies in the radio modules of one delivery, the scale of the problem is unknown. A dozen units may be affected, or the whole batch.
Take a batch of modules for 200 pieces. It went into 200 controllers, and 140 reached dealers: 70, 45 and 25 units to three buyers. Another 60 controllers sit in stock. Both groups need a check, but the decisions differ.
How do you set up serial number tracking for electronics in Bimp?
The scenario has six steps. A help article sits next to each.
Step 1. The tracking mode. In the company accounting settings turn on tracking by batches and by serial numbers. In the controller card, in the “Accounting” section, turn on “Use batches”, “Use serial numbers” and “Series balance control”. This is strict mode: a sale or write-off without choosing a series is impossible. For a product under warranty informational mode is weaker, because it does not block shipment without a series. Details in the help: Serial numbers.
Step 2. Radio modules with series. Modules arrive from the supplier with a “Goods receipt” document. The warehouse worker opens the “three dots” menu next to the module, chooses “Scan barcodes” and scans the numbers in the “Series creation” panel. If fewer series are scanned than the row holds, Bimp splits the row: the scanned units get series, and the rest stay without one. So before transferring to the document, check the counters at the bottom of the panel: “Must be registered” and “Registered”. The description is in the article Receipt with serial numbers.
Step 3. The production order and the production task. In the production order for 200 controllers click Create batches, and the system splits the products into series of one unit each. Production tasks are created from the order: one task, one unit, one series. If materials are reserved, they pass into the task with the batch and series preserved (Reserve materials). The process engineer opens the task and sees which batch the module in this unit came from. See Production tasks and Production order.
Step 4. A sale with a series chosen. The manager processes a “Sales of goods and services” document for the dealer and picks specific units from the list of available series. In strict mode the document will not go through without the choice. The dealer who received a unit is recorded in the document together with its serial number (Shipment).
Step 5. The claim. The serial number is entered in the search in full, including the letters at the start: partial search does not work. Then open the product card, the “Movement” tab and turn on “Show archive”, because a sold unit is hidden by default. There you see the documents the unit passed through, from assembly to shipment (Searching and scanning serial numbers).
Step 6. Return and repair. The dealer returns one series from a sold batch: in the sales document you clear the marks on all series, leave one and create a return based on it (Returning a batch series). The repair is processed as a production order with the operation type “Repair”. There you choose the unit from stock, give the batch and series, and the price is calculated as the unit’s cost plus spare parts and operations.
A dealer returned one controller from a batch of 200. Analyzing the claim took a working day, and the scale of the problem with the radio modules stayed unknown.
Strict serial tracking, receipt of modules with series, a production task for every unit, a sale with a chosen series, search by serial number and a repair as a separate order.
Claim analysis fell from 8 hours to 15 minutes. Out of 12 claims a month that is 96 - 3 = 93 hours saved. A repair costs €11 per unit, and this sum is visible separately from the cost of a new unit.
How does a claim analysis by serial number look?
The controller is back. The process engineer enters its full number in the search, opens the unit card and sees the assembly date, the production task and the batch of the radio module. The dealer is found in the sales document where this number was chosen.
Next you need to find out how many units are affected. In the module card you open the batch in question and see how many units went into production. For this there is the “Stock movement” report with the filters “Batch number” and “Series” (Stock Movement report). The assembly documents that used this batch show the material batches on the “Materials” tab. The scenario has no ready report “where did this batch of modules go” in one click, so the answer is built from two documents and takes minutes.
For our batch the answer is as follows.
| Group | Quantity, pcs | What to do |
|---|---|---|
| Sold to dealer 1 | 70 | ask the dealer, check by series |
| Sold to dealer 2 | 45 | ask the dealer, check by series |
| Sold to dealer 3 | 25 | ask the dealer, check by series |
| In stock | 60 | stop shipments, check the modules |
| Total | 200 |
Check: 70 + 45 + 25 = 140 sold, 140 + 60 = 200.
How much does a warranty repair cost, and why does it need its own cost?
A production order with the type “Repair” calculates the price differently from assembly. For assembly the unit price equals materials and operations. For a repair, the cost of the unit being repaired is added to that sum.
Take notional figures. The controller costs €46. Replacing a radio module costs €8, and the process engineer’s work takes half an hour at €6 per hour, which is €3. The repair expenses are 8 + 3 = €11. In the production order the unit after repair is valued at 46 + 11 = €57.
This way warranty expenses are visible separately. Over a quarter, 9 units from this batch came back: 9 × 11 = €99. If you replaced the modules in all 140 sold controllers, the maximum sum would be 140 × 11 = €1,540. The owner sees both numbers and decides whether to recall the whole batch or respond to dealer claims. For the 60 controllers in stock there are no replacement costs yet, and they can be calculated before shipment.
What should you prepare before launching serial tracking?
Serial tracking works when data reaches the system on time. For Gravent Controls the preparation took a week and consisted of four actions.
- Make a list of the products and components that carry series. Under warranty are the finished controller and the radio module. Resistors and connectors need no series and are kept by batches or by quantity.
- Agree with the module supplier that every delivery comes with a list of series or barcodes on the units. Without this the numbers are typed by hand, which is 200 numbers per batch.
- Explain the strict mode rule to the warehouse: the system will not post a shipment without a chosen series, so the series is looked up before the truck stands waiting to be loaded.
- Agree with dealers that every claim names the full serial number of the unit. Search works only on a full match, and one missing “GC” at the start of the number returns “not found”.
The first two batches are assembled with spare time, to check the whole chain from scanning to search. If this stage shows that some modules have no series, it is better to reorder them before launching serial tracking.
What does this give the company?
The owner gets the answer to “what if the defect is widespread” in minutes. The process engineer does not rebuild a unit’s history from three tables. The warehouse manager sees how many units with the suspect batch are in stock and stops shipments. The service engineer processes a repair with a document that has its own cost, and a log entry is no longer needed.
Bimp is a Ukrainian cloud ERP for manufacturers, and the whole chain from module receipt to a dealer’s return works in one system. The strict and informational modes work the same way for any serial-tracked product, and the help article Serial numbers compares them in a table. How to tie a delivery of components to a finished unit is described in the help section on production tasks.
Scenario limits
The scenario shows a unit with serial tracking and batches of components. The “Stock movement” report gives movement by batches and series, and the list of units that contain a component of a certain batch is assembled from production tasks and assembly documents. Search by series works only on a full match. Everything depends on discipline when series are entered: if modules arrived without series, the link between a unit and a batch cannot be built. Some help articles the steps rely on carry a verification status, so check the button names against your version.
How to set up such tracking for your product is described on the page Electronics manufacturing in Bimp.
FAQ
Can you keep serial number tracking for electronics without strict mode?
Yes. In informational mode series are only recorded in the batch, and sales documents are not blocked. For warranty service strict mode is better: a manager cannot process a shipment without choosing a specific series.
Why does Bimp not find a unit by part of its serial number?
Series search works only on a full match, including the letters at the start of the number. The most reliable way is to scan the barcode or copy the number without extra spaces.
Where can you see the history of a specific serial number?
On the "Movement" tab of the product card. If the unit is already sold, turn on the "Show archive" switch, otherwise the series is hidden.
How do you process a warranty repair in Bimp?
Create a production order with the operation type "Repair", choose the unit from stock and give its batch and serial number. The cost of spare parts and work is added to the cost of the repaired unit.
In a Bimp ERP demo a specialist shows how to find the batch of components and the dealer for one serial number of your product.
Book a demo